Napoleon fireplace refusing to light, clicking or shutting itself off? Sound Comfort offers Napoleon fireplace repair across Snohomish County, from Lake Stevens and Everett to Granite Falls and Stanwood. We find the failed part, you approve the upfront price first, and many repairs finish in one visit.
















Napoleon builds a wide range of gas fireplaces, and each style fails in its own way. A tech who reads ignition systems daily saves you guesswork.
Many Napoleon models come with either a standing pilot or electronic ignition, and we repair both kinds.
Thermocouple, thermopile, igniter, receiver or valve: we test each in order and replace only the part that truly failed.
Licensed, bonded and insured, we check the gas connections and the flame before we close the unit back up.
Our shop is in Lake Stevens, and we drive out to Napoleon owners in every part of Snohomish County.
Napoleon sells fireplaces in many series, and the trouble you see depends on the family and its ignition style. These are the four areas where we get the most calls.
These direct vent fireplaces are popular in newer builds across the county. Many offer a choice between a standing pilot and electronic ignition, which changes how they fail. Millivolt units need a hand-lit pilot, while electronic ones light on their own.
Pilot goes out or will not light
Burner drops while pilot stays on
No spark from the igniter
Appliance keeps shutting off
Many Napoleon valves block relighting for about a minute until the thermocouple cools. If it still will not hold, a weak thermocouple, a small pilot flame or air in the line is likely.
A pilot flame that does not fully engulf the thermopile is a common cause. Wall switch wiring that is too long or a bad switch can also drop the burner.

Napoleon inserts turn an old open hearth into a real heater, which is why they are common in older Snohomish County homes. They need household power for the ignition module and blower, so an outlet or battery issue can look like a gas problem.
Ignition module not powering up
Blower will not run
Glass film or soot
Venting and draft checks
Check the power connection and the batteries in the remote and receiver first. If those are fine, the module, receiver or a safety switch may need testing.
A white or gray haze can come from sulfur in the fuel. Clean it with a fireplace glass cleaner, only when the glass is fully cool.

Linear and see-through Napoleon models show off a long flame, so any flicker, delay or uneven burn stands out. Their larger burners and glass fronts need clean ports, a tight seal and steady gas pressure to look right.
Slow or noisy startup
Uneven or lazy flame
Cloudy glass on both sides
Gas pressure concerns
Plugged burner ports, shifted media or a pressure problem are the usual causes. We clean the burner, reset the media and check the gas pressure against the rating plate.
See-through models have two panes to care for, and cleaning has to wait until they are cool. If soot returns quickly, we look for the cause.

Napoleon's eFIRE app and handheld remotes run the flame, blower and lights, but they depend on batteries and a working receiver. When the controls go quiet, the fireplace itself may be fine and the receiver or battery holder may be the fault.
Remote loses pairing
App cannot connect
Receiver battery problems
Pilot noise with no spark
Often not. Start with fresh batteries in both the remote and the receiver. If it still fails, the receiver may need to be reprogrammed or replaced by a technician.
Some models allow manual operation, but follow your manual exactly. If anything seems wrong, stop and call us rather than forcing it, because a safety control may be involved.


Call or send the form with your model name and what it does when you try to light it.
We diagnose the fault and give you a clear, upfront price. Work starts only after your okay.
We fix it, test the full lighting cycle, check for leaks and leave your hearth tidy.
A Napoleon fireplace is built to run reliably for years, but sensors and igniters do wear out. Catch a problem early and the repair is usually simpler. These are the warning signs worth acting on:
Pilot fails to light or hold
Burner shuts off after minutes
Clicking sound with no flame
Remote or app stops responding
If you smell gas: do not try to light the fireplace or use switches. Get everyone outside, then call 911 or your gas utility from there. Puget Sound Energy: 1-888-225-5773. Once it is safe, call us at (425) 225-4756.

Napoleon recommends a yearly inspection of the appliance and its venting. A few simple habits between visits help it start on the first try.
Many electronic models take AA cells in the receiver and AAA cells in the remote. Check your manual, then use new alkaline batteries each fall.
Use a gas fireplace glass cleaner on a cool pane. Cleaning hot glass can bake residue on and may damage it.
If your fireplace runs on propane, an empty tank looks exactly like a pilot failure. Check the gauge before you call.
A technician can test the pilot, clean the burner, inspect the venting and check for leaks before cold weather returns.
Any gas fireplace sends exhaust outside through its vent. A damaged gasket, cracked glass or blocked termination can let carbon monoxide into your living space, and you cannot smell it. Keep CO alarms working near bedrooms and on each floor. If one sounds, get everyone outside and call 911 first.
One yearly visit cleans the pilot and glass, tests the controls and checks for gas and carbon monoxide, so your Napoleon is set when the first cold snap hits.
Only need one Napoleon tune-up? Schedule it online or give us a ring.
Yes. We service Napoleon gas inserts, built-in fireplaces and stoves across Snohomish County, whether they use natural gas or propane. Tell us the model when you call and we will arrive prepared. Have a different make? We also repair Regency and Heat & Glo fireplaces.
Look for the rating plate, which is usually near the control area or inside the lower panel. A photo of it helps us line up the right parts before the visit.
We cover Snohomish County broadly, including Lake Stevens, Everett, Marysville, Snohomish, Monroe, Arlington, Stanwood and Granite Falls. If you are nearby, ask and we will check the schedule.
Common causes are a worn thermocouple, a pilot flame that is too small, a dirty pilot assembly or an empty propane tank. We test each one so the right part gets replaced.
A light white film is common and comes from the fuel. Heavy black soot is different, because it signals a flame that is not burning cleanly and needs attention.
Millivolt models usually run without house power. Electronic units rely on battery backup, so fresh batteries matter before storm season. We can check yours during a visit.

