- 100% Satisfaction Guarantee
- 0% Financing Available
- 24 HR Emergency Service
- 5-Star rating
Pilot won’t stay lit, burner clicking with no flame, or blower rattling? We offer fireplace repair in Lynnwood for gas inserts, stoves, log sets and outdoor units. You approve the price before we begin, and most repairs wrap up on the first visit.
Many Lynnwood houses have natural gas at the meter, so a gas fireplace is part of the heating system. It deserves a technician who works on gas controls daily.
We work on thermocouples, pilot assemblies, valves, igniters and control modules daily, and we replace the part that actually failed instead of guessing.
Licensed, bonded and insured in Washington. We test fittings for leaks and confirm a clean flame before we pack up our tools.
Common ignition and sensor parts ride with us, so many repairs are finished on the first trip rather than a second appointment.
We also service furnaces, heat pumps and mini-splits, so one visit can cover every heat source in your Lynnwood home.
Lynnwood has 1960s ramblers with old masonry hearths, newer townhomes with direct vent units and patios built for evenings outside. Find your type below for the faults we handle most.
A gas insert slid into a brick hearth turns a decorative opening into a real heater, which is popular in mid-century Lynnwood homes. Because the unit sits inside a firebox, small faults show up fast: a pilot that drops out, a burner that quits after a few minutes or a fan that rattles.
Pilot that goes out repeatedly
Clicking igniter with no flame
Burner shutting off after minutes
Blower noise or weak airflow
A safety circuit is usually closing the gas valve. Weak thermopile output, a dirty pilot or a venting restriction can each trigger it, so we test the signal and clear the vent path.
No. Cracked glass can let exhaust into the room and may fail further when hot. Turn the fireplace off, let it cool, and call us before using it again.
Gas stoves are common in finished basements and family rooms where there is no hearth at all. They heat a room fast, but they depend on clean ignition, a quiet blower and a tight vent connection. When one acts up, you feel the chill quickly.
Slow or delayed ignition
Rattling or humming blower
Flame that looks lazy or yellow
Remote or wall switch not responding
Yes, get it checked. Delayed ignition lets gas build up before it lights, often from a weak pilot or dirty ports. Don’t keep restarting it; call us instead.
Often the cause is simpler: dead remote or receiver batteries, a lost pairing or a switch left in the wrong position. If fresh batteries don’t help, we test the receiver and valve.
Log sets sit in many older Lynnwood fireplaces and give a wood-fire look without the ashes. They are sensitive to burner cleanliness, log placement and gas pressure, so odd flames or smells usually have an ordinary cause we can correct.
Sooty logs or blackened glass
Pilot that will not hold
Burner that hisses or pops
Flames that burn only on one end
Soot means the flame isn’t getting enough air or touches a log. Shifted logs, clogged ports and wrong gas mixture are typical causes. We reset the logs and tune the burner.
Log sets are designed as a matched system with the burner. Mixing parts can block flame paths and create soot or carbon monoxide, so let us confirm any change.
Outdoor gas features around Lynnwood decks and patios sit through months of rain, fir needles and dampness. Burners clog, igniters corrode and wiring gets wet, so a unit that worked in September may not light after a rainy winter.
Water or debris in the burner
Corroded igniter or loose wiring
Weak flame on the fire table
Propane tank or regulator issues
Moisture on the igniter, spiders in the burner tube or a tripped safety are common. We dry, clean and test the ignition parts and check the gas supply.
A vented cover that keeps out rain and needles helps, but only once the unit has cooled completely. Never cover it while hot or leave a sealed cover on a burner.
Reach us by phone or online. Tell us the brand and what it is doing, and we set a visit time.
Our tech finds the fault, explains it in plain language and gives you a price. We start only once you agree.
We complete the repair, test the flame and gas connections, tidy the area and show you how to use any new settings.
Even a fireplace used only on weekends collects dust, soot and wear. A short yearly routine keeps it igniting first try on a cold, windy night.
Lint and pet hair collect around the pilot and burner over summer. A technician cleans them out, which prevents delayed ignition and uneven flames.
Weak batteries in a remote or receiver cause a surprising number of no-light calls. Swap them each fall, and use quality cells because heat drains cheap ones.
A hazy film forms on the glass from normal combustion. Use a cleaner made for fireplace glass only after the unit has cooled, and never an abrasive.
Many electronic fireplaces have a battery backup for outages. Learn where the switch is now, so a winter storm doesn't leave you hunting for it in the dark.
A blocked or leaking vent, a cracked glass panel or a poorly burning flame can put carbon monoxide into your living space, and you cannot smell it. Install a working CO alarm on each level and near bedrooms, test it every month, and get the fireplace inspected yearly.
Fireplaces rarely fail without a hint. Igniters weaken, sensors drift and burners clog gradually. Catching the early signs usually means a smaller repair, and avoids being stuck without your backup heat during a windy, outage-prone night.
Smell gas? Don’t light anything or touch switches. Get everyone outside, then call 911 or Puget Sound Energy at 1-888-225-5773. Once the utility says it’s safe, call us at (425) 225-4756 for the repair.
One annual visit cleans the pilot and glass, checks the burner, vent and gas connections, and keeps you first in line when something fails on a cold Lynnwood evening.
Need only one tune-up this year? Book a single visit online or call us.
All of them, from Alderwood Manor and Lake Serene to Meadowdale, College Place and the City Center area. We drive in from our Lake Stevens shop and answer the phone any hour.
Millivolt and standing-pilot units often run without power. Electronic units need their battery backup, and blowers stop. Check the battery now rather than during the next windstorm, since the November 2022 storm hit Lynnwood hard.
A dusty or warm smell on the first run of the season is normal and fades. A smell that lingers or smells like gas is not, so shut it off, and if it is gas, leave immediately.
Yes, we service most major gas fireplace, insert and log set brands. See our Heat & Glo repair page for details on those families.
Clicking without flame means the spark fires but the pilot isn’t catching. Causes include a dirty pilot, bad gas supply, a failed igniter or a weak sensor. Don’t keep trying; call us.
No, we focus on gas fireplaces, inserts, stoves, log sets and outdoor gas fire features. We don’t do wood-burning or chimney work, but we will happily help with anything gas.
